|
X3IR Installation
and Information -- Posted by XanTium
on January 11 13:59 EST Thank you XBOX
SCENE
installation instructions of the Xecuter(info) X3IR (IR-addon):
X3IR Description: Weight: 20g / per piece
Features:
1. Blue status led
2. Compatible with any modchip
3. Enable/Disable Modchip upon boot.
4. Easy to use programming software
5. Learning functionality allows virtually any remote control
to be used
6. User programmable buttons for all functions, such as wich
button turns on the xbox or turns it off
7. Safety Off (tm) makes sure you press the 'OFF' button 3
times before turning off the xbox to prevent unintended xbox
shutdown
8. Turn ON and OFF the XBOX with the XBOX Dvd remote control,
and any RCA DVD compatible remote (and there are hundreds
of these)
9. Perfect-Press (tm) - The length of emulated press of front
panel 'Power' button can be finely tuned to work with any
modchips' needs (ie. long press is 100msec - mod on, short
press is 10msec - mod off)
10. Soldering for non X3 Owners
11. PDF Programming Guide HERE
12. PDF Installation Guide HERE
13. PDF Features and Use Guide HERE
X3IR -
Installation instruction:
Xbox-Scene
1. Tear
off the CR sticker, and stick it on the back side of IR PCB.
2. Remove
2 screws of X3CP as photo.
3. Turn
component side of LED PCB up, and stick the IR PCB at the
location as photo.
4. Turn
around the 3 wires to go backside of LED PCB and screw on
the 2 screws as photos.
5. Plug
the white cable into the connecter of the Programer, and go
through the both white cable and IR cable to the hole of XBOX
as photos.
6. Plug
3Pin, 5Pin(Pitch1.0) and 5Pin(Pitch1.25) cables into the X3IR
mainboard and 2Pin cable into X3 Reset-Eject board, and then
stick mainboard at the location as photos.
7. Install
the programer at the bottom of X3CP with CR sticker as the
below photo.
8. Turn
ON and OFF the XBOX with the XBOX Dvd remote control, and
any RCA DVD compatible remote (and there are hundreds of these)
9. Perfect-Press (tm) - The length of emulated press of front
panel 'Power' button can be finely tuned to work with any
modchips' needs (ie. long press is 100msec - mod on, short
press is 10msec - mod off)
10. Soldering for non X3 Owners (thank you to Xboxchopshop,
for this part of the tutorial)
Mount the IR Receiver. This is the tiny board with the black
led on it. It comes with double-sided sticky pad, so you can
stick it wherever you want. There is a spot in an X3 Control
Panel and the X3 ProSwitch to put it, or you can run it out
under a controller port and stick it under the front panel
where it will be able to receive a signal.
Mount the Programmer Port. This is optional. Only install
this ugly attachment if you need to program the x3ir to work
with another remote. Even if you do, I would leave it hanging
with the lid off the xbox while you reprogram, then take it
off. Keep it if you want, but I just thought it was an eyesore.
Ok, we made it past the obvious, let's hook up the wires.
It has 3 loose wires (Red1, White, Black) and 2 short red
wires with a plug (Red2, Red3). Here is the wire harness:
If you have an X3 modchip, then the plug needs to be hooked
up to this part that came with the X3 package.
If you do NOT have an X3 modchip, then cut off the plug and
strip the ends of the wires. The 3 or 5 loose wires need to
be soldered to the bottom of the motherboard, underneath the
powersupply plug. Use the diagrams below to figure out where
the wires need to go. Remember Red2 and Red3 only need to
be soldered if you don't have an X3 chip, and make sure you
use the diagram for your
version xbox.
11. PDF Programming Guide HERE
12. PDF Installation Guide HERE
13. PDF Features and Use Guide HERE
|
